 | Prince Tie-Rod Cylinder - 3000 PSI, 2 1/2in. Bore, 24in. Stroke, 1 1/4in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 2 1/2, Stroke Length (in.): 24, Closed Pin Center (in.): 34 1/4, Shaft Diameter (in.): 1 1/4 | *$179.99 |
 | Standard Half Coupling - 7/16in. Size
Brand: Northern Tool Equipment
Use a flex coupling to direct-mount your engine to pump. Oil-resistant synthetic rubber inserts are used between the coupling halves to provide an equalized cushioned drive. When ordering, get one side to fit the motor and the other side to fit the pump shaft dia. Order two halves plus insert for complete coupling. When mounting, do not pound on the end of your pump shaft. U.S.A. Shaft Diameter (in.): LO95 HUB 7/16, Fits Models: LO90, LO95, Max. HP: 11.16, Max. Torque (in.-lbs.): 194, Max. RPM: 3,600, Material Type: Synthetic Rubber, Keyway (in.): 3/32 x 3/64 | *$13.99 |
 | De-Sta-Co Hydraulic Power Workholding, Block Cylinder, Double Acting, C=2.68, O=1/2-13 (1 Each)
Brand: De-Sta-Co Part Number: 090-023-333 | *$291.50 |
 | Buyers Flush-Face Coupler - 1/2in. Female; 3/4in. Port NPT, Model# FF0812
Brand: Buyers
Push-to-connect design, no need to retract the sleeve to connect. Locking sleeve prevents accidental disconnection during operation. Fitting Size (in.): 1/2 F x 3/4 NPT, Max. PSI: 5,000, Locking Sleeve: Yes | *$69.99 |
 | Lion Heavy-Duty Tie-Rod Cylinder - 2500 PSI, 4in.Bore, 24in.Stroke, 1 1/2in. Shaft, Model# 40TL24-150
Brand: Lion 2500
Built tough for agricultural and industrial applications. Rated for 2500 PSI continuous working pressure and designed to withstand shock loads of up to 5000 PSI. Durable ductile iron cast components. 90 durometer O-ring seals with anti-extrusion rings for positive sealing throughout the cylinder. High-tensile steel shaft is precision ground, polished and hard chrome plated. 8in. stroke cylinders threaded rods accept adjustable stroke controls. 2in. and 2 1/2in. bore cylinders have 3/8in. working ports; 3in., 3 1/2in. and 4in. bore have 1/2in. working ports. ALL have 1in. pin holes. Max. PSI: 2,500, Bore Diameter (in.): 4, Stroke Length (in.): 24, Closed Pin Center (in.): 34 1/4, Shaft Diameter (in.): 1 1/2 | *$199.99 |
 | Enerpac Hydraulic Power Workholding Single Acting Manifold Cylinder, No. TS-9131ST (1 Each)
Brand: Enerpac Part Number: CST9131
These threaded miniature cylinders were designed specifically for tooling. All cylinders are single-acting with spring return action for rapid work release. They have threaded bodies for all types of mountings. Cylinders may be inserted directly in a fixture or used with standard brackets. Stainless steel construction. Maximum operating pressure 5,000 psi. See our full line catalog for accessories. | *$110.00 |
 | Heavy-Duty Half Coupling - 1 1/8in. Size
Brand: Northern Tool Equipment
Use a flex coupling to direct-mount your engine to pump. Oil-resistant synthetic rubber inserts are used between the coupling halves to provide an equalized cushioned drive. When ordering, get one side to fit the motor and the other side to fit the pump shaft dia. Order two halves plus insert for complete coupling. When mounting, do not pound on the end of your pump shaft. U.S.A. Shaft Diameter (in.): LO99 HUB 1 1/8, Fits Models: LO99, L100, L110, Max. HP: 23, Max. RPM: 3,600, Material Type: Synthetic Rubber, Keyway (in.): 1/4 x 1/8 | *$19.99 |
 | De-Sta-Co Hydraulic Power Workholding, Threaded Cylinder, 1 7/8-16 thds., Stroke=.500 (1 Each)
Brand: De-Sta-Co Part Number: 010-211-502
Single-acting with spring return action, these cylinders can be used singly or combined by using a common manifold. Easily mounted. Can be used in any attitude and requires only a single inlet port. Threaded cylinders can be directly inserted into a fixture or used with mounting blocks. Locknuts, mounting blocks and end caps are available. Call for price and delivery. The 1-5/16" through 2-1/2" diameters are furnished with a radial port as well as axial. | *$156.30 |
 | Dynamic Fluid Components High Pressure Hydraulic Gear Pump - 3650 Max. PSI, 3/4in. Shaft, Model# GP-F20-08-P1-C
Brand: Dynamic
The Dynamic Fluid Components high pressure hydraulic gear pump features all aluminum construction and produces displacement of 0.48 cu. in./rev. | *$175.99 |
 | Apache Hose Belting, Inc. 98398238 Universal Hydraulic Hose
Brand: Apache Hose Part Number: 98398238
Assemblies. 2 wire. Assemblies: Hose and couplings meet 100R2AT specification. 3 8" I.D.: 4000 P.S.I. (W.P.), 16,0000 P.S.I. burst, 5.12" minimum bend radius, coupled 3 8" MNPT on each end. 1 2" I.D.: 3500 P.S.I. (W.P.), 14,000 P.S.I. burst, 7.09" minimum | *$11.09 |
| Prince Tie-Rod Cylinder - 2500 PSI, 3in. Bore, 8in. Stroke, 1 1/8in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 2500 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 2,500, Bore Diameter (in.): 3, Stroke Length (in.): 8, Closed Pin Center (in.): 20 1/4, Shaft Diameter (in.): 1 1/8 | *$149.99 |
 | De-Sta-Co Hydraulic Power Workholding, Threaded Body Cylinder, Double Acting, D=1.875-16, K=5/16-24 (1 Each)
Brand: De-Sta-Co Part Number: 010-022-225 | *$176.92 |
| Standard Half Coupling - 7/8in. Size
Brand: Northern Tool Equipment
Use a flex coupling to direct-mount your engine to pump. Oil-resistant synthetic rubber inserts are used between the coupling halves to provide an equalized cushioned drive. When ordering, get one side to fit the motor and the other side to fit the pump shaft dia. Order two halves plus insert for complete coupling. When mounting, do not pound on the end of your pump shaft. U.S.A. Shaft Diameter (in.): LO95 HUB 7/8, Fits Models: LO90, LO95, Max. HP: 11.16, Max. Torque (in.-lbs.): 194, Max. RPM: 3,600, Material Type: Synthetic Rubber, Keyway (in.): 3/16 x 3/32 | *$13.99 |
| Dynamic Fluid Components High Pressure Hydraulic Gear Pump - 3650 Max. PSI, Spline 9-Tooth Shaft, Model# GP-F20-08-S9-C
Brand: Dynamic
The Dynamic Fluid Components high pressure hydraulic gear pump features all aluminum construction and produces displacement of 0.48 cu. in./rev. | *$185.99 |
 | Enerpac Hydraulic Power Workholding Swing Cylinder Short Arm No. CAS-121, Use w/cap.=2,600 lbs. (1 Each)
Brand: Enerpac Part Number: CAS-121
These clamp arms are designed for use with the swing cylinders shown above. Clamp arms can be positioned and tightened without removing the swing cylinder from the fixture. Clamp arm design eliminates the use of a vise when securing to a plunger. Short arms have a tapped hole for buttons and toggle pads. Long arms can be shortened to desired length. | *$53.00 |
| Prince Tie-Rod Cylinder - 2500 PSI, 4in. Bore, 8in. Stroke, 2in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 2500 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 2,500, Bore Diameter (in.): 4, Stroke Length (in.): 8, Closed Pin Center (in.): 20 1/4, Shaft Diameter (in.): 2 | *$229.99 |
 | De-Sta-Co Hydraulic Power Workholding, Flange Mounting Bracket, A=1.5, B=1.12, C=1 1/8-16 (1 Each)
Brand: De-Sta-Co Part Number: 052-112-160
Flange mounting brackets allow you to secure your swing/pull clamps in two ways. You may use the set screw and nylon thread protector ball (supplied) or simply lock the clamp using an optional jam nut. Swing clamps may also be screwed into a threaded hole and locked in position with a jam nut. | *$58.21 |
 | Apache Hydraulic Hose - 100ft.L x 1/4in. Dia., 2750 PSI, Model# 98392203
Brand: Apache Hose
Boxed hydraulic hose. Cut it to length needed and attach reusable couplings (couplings sold separately). SAE 100R1, type AT. Hose Diameter (in.): 1/4, Hose Length (ft.): 100, Working Pressure (PSI): 2,750, Bursting Pressure (PSI): 11,000 | *$89.99 |
 | Enerpac Hydraulic Power Workholding Hollow Cylinder, No. CY2129-5 (1 Each)
Brand: Enerpac Part Number: CY2129-5
These hollow cylinders combine compactness with power and versatility. Any application requiring either a pushing or pulling action is easily handled with this type of cylinder. The cylinders are threaded and can be placed over a bolt or a stud to upgrade most existing manual clamping fixtures. | *$366.00 |
| Dynamic Fluid Components High Pressure Hydraulic Gear Pump - 3650 Max. PSI, 3/4in. Shaft, Model# GP-F20-10-P1-A
Brand: Dynamic
The Dynamic Fluid Components high pressure hydraulic gear pump features all aluminum construction and produces displacement of 0.61 cu. in./rev. | *$175.99 |
| | De-Sta-Co Hydraulic Power Workholding, Spring Advance Work Support, Capacity=7,500 lbs. (1 Each)
Brand: De-Sta-Co Part Number: 040-1-7500
Hydraulic Power Workholding - Spring Advance Work Supports | *$283.05 |
 | De-Sta-Co Hydraulic Power Workholding, Block Cylinder, Single Acting, C=3.651, O=5/16-24 (1 Each)
Brand: De-Sta-Co Part Number: 090-012-224 | *$290.92 |
 | Northman Fluid Power Modular Hydraulic Flow Control Valve - 9.3 GPM, 3000 PSI, Ports A B, Reverse Free Flow, Model# MT02
Brand: Northman Fluid Power
This Northman flow control valve is designed to restrict the flow of oil in a hydraulic system to control the speed of a cylinder or motor. The flow in one direction is metered as adjusted. The flow in the opposite direction is a free flow over a check valve. Valve mounts as a modular unit between a D03 size directional control valve and the subplate. Contains 2 separate pilot-operated check valves-one each on A cylinder port and B cylinder port. Allows metered flow adjustment in the cylinder ports as the flow exits, controlling the speed of the cylinder. As separate valves, speed may be controlled independently for the extend and retract operations. Requires longer than standard bolt kit to mount this flow control in valve stack. | *$79.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 5in. Bore, 30in. Stroke, 2in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 5, Stroke Length (in.): 30, Closed Pin Center (in.): 42 1/4, Shaft Diameter (in.): 2 | *$379.99 |
 | Enerpac Hydraulic Power Workholding Work Support, Spring Advanced, No. WSL-111 (1 Each)
Brand: Enerpac Part Number: WSL-111
Work supports provide additional support to avoid excessive movement or deflection of the workpiece during machining. When hydraulic pressure is applied to the work support, a piston pushes against an internal adjustable spring that advances the work support plunger against a workpiece at the force set by the adjustable spring. As more hydraulic pressure is applied, an internal sleeve will grip and lock the plunger in that position. Available as a spring or fluid advance unit. The spring advanced unit can be converted to air by simply removing the internal adjustment spring and attaching a low pressure air line to the air breather vent tube. Operating pressure is 700 psi minimum, 5,000 psi maximum. | *$207.00 |
 | Northman Fluid Power Hydraulic Directional Control Valve - 10.7 GPM, 4500 PSI, 3-Position, Double Solenoid, Tandem Center Spool, 12 Volt DC Solenoids, Model# SWH-G02-C3-D12-10
Brand: Northman Fluid Power
This industrial hydraulic directional control valve conforms to the National Fluid Power Association (NFPA) D03 mounting pattern for subplate or manifold mounting. As a four-way valve, it is commonly used to extend and retract a double-acting hydraulic cylinder or to control a rotary hydraulic motor. As a spring-centered valve, it will remain in its home position with P and T ports commonly connected until shifted electrically to one of two positions to either extend or retract a cylinder, returning to home when the power is removed. Its molded coils are moisture and dirt resistant. Indicating signal lights, manual override, bolt kit and electrical junction box are standard. The valve mounts on Northern Tool Subplate 203221 with 1/4in. NPT ports or 203231 with 3/8in. NPT Ports. | *$109.99 |
 | Ball Valve - 1/4" Full Port Forged Brass IPS (600WOG/150WSP)
Brand: DuraChoice Model: WB4170 Part Number: 41700 | *$6.02 |
 | De-Sta-Co Hydraulic Power Workholding, Swing/Pull Clamp Arm, A=3.268, B=.866, C=M10 (1 Each)
Brand: De-Sta-Co Part Number: 031-S-2400
Custom built arms of any length must clamp to the swing/pull clamp's piston rod in a manner similar to the arms or some derating of the clamp will be necessary. IMPORTANT: Any clamp using a modified or custom arm that is longer or heavier than standard arms must be derated to prevent internal damage. | *$50.50 |
 | Dynamic Fluid Components High Pressure Hydraulic Gear Pump - 2900 Max. PSI, Spline 9-Tooth Shaft, Model# GP-F20-16-S9-A
Brand: Dynamic
The Dynamic Fluid Components high pressure hydraulic gear pump features all aluminum construction and produces displacement of 0.97 cu. in./rev. | *$185.99 |
 | Lion Welded Hydraulic Cylinder - 3000 PSI, 3in. Bore, 18in. Stroke, Model# 644825
Brand: Lion 3000
Double-acting, double-ported welded tie rods are perfect for industrial, agricultural and contractor applications. Features chrome rod, crown piston seals with wear ring, hallite rod seals, double lug base end, threaded rod end with ductile rod clevis and 3/4-16 ORB (SAE 8) ports inline with pins. 1in pin hole size. Complete with pins and cotter pins. | *$189.99 |
 | Northman Fluid Power In-Line Hydraulic Check Valve - 17.1 GPM, 3000 PSI, 1/2in. NPT Ports, Model# CIT0405
Brand: Northman Fluid Power
This Northman in-line check valve is designed to allow free flow of oil in a hydraulic system in one direction and block flow in the reverse direction. | *$24.99 |
 | Lion Welded Hydraulic Cylinder - 3000 PSI, 4in. Bore, 8in. Stroke, Model# 644848
Brand: Lion 3000
Double-acting, double-ported welded tie rods are perfect for industrial, agricultural and contractor applications. Features chrome rod, crown piston seals with wear ring, hallite rod seals, double lug base end, threaded rod end with ductile rod clevis and 3/4-16 ORB (SAE 8) ports inline with pins. 1in pin hole size. Complete with pins and cotter pins. | *$189.99 |
| Lion Welded Hydraulic Cylinder - 3000 PSI, 2in. Bore, 24in. Stroke, Model# 644807
Brand: Lion 3000
Double-acting, double-ported welded tie rods are perfect for industrial, agricultural and contractor applications. Features chrome rod, crown piston seals with wear ring, hallite rod seals, double lug base end, threaded rod end with ductile rod clevis and 3/4-16 ORB (SAE 8) ports inline with pins. 1in pin hole size. Complete with pins and cotter pins. | *$159.99 |
 | Metro Machine Lock Valve-4 Port, Model# 408-04
Brand: Northern Tool Equipment
Pilot operated check valve is designed to lock a cylinder or part of a circuit while a control valve is in neutral position. Double internally pilot operated. Holds circuit at desired pressure while in transport or working. Eliminates replacing worn spools and old valves. Rugged construction; made of high strength anodized aluminum with hardened and ground ball seats. Applications include loaders, outriggers, back-hoes, work platforms and cranes. Rated at 15 GPM, 3000 PSI. Semi-adjustable, with 1/2in. port pipe thread. | *$79.99 |
 | Apache Hydraulic Hose - 1/2in. x 21in.L, 2-Wire, 3500 PSI
Brand: Apache Hose
This Apache hydraulic hose is designed for use with petroleum- and water-based hydraulic fluids. Can handle gasoline, diesel fuels, mineral oils, glycol, lubricating oils and more. Hose Diameter (in.): 1/2, Hose Fitting Size (in. NPT): 1/2, Hose Length (in.): 21, Working Pressure (PSI): 3,500 | *$11.99 |
 | De-Sta-Co Hydraulic Power Workholding, Semi Automatic - Air/Hydraulic Booster, A=4.5, B=10.875 (1 Each)
Brand: De-Sta-Co Part Number: 039-101-000DE
Converts normal shop line air pressure to high pressure hydraulic power. With the system filled, the volume of oil required to actuate a cylinder or pressure point is only equal to the cubic content of the piston displacement. Boosters have built in manifold and are made of corrosion and wear-resistant materials. Hydraulic piston tube has wear rings and the air piston is self centering for long life. Boosters offer automatic relief of system overcharge as well as complete automatic bleeding with each return, eliminating prefilling. Large volume visible oil reservoir automatically replenishes the system with available reserves. 100 psig max. input air pressure. | *$753.51 |
| Dynamic Fluid Components High Pressure Hydraulic Gear Pump - 2900 Max. PSI, 3/4in. Shaft, Model# GP-F20-20-P1-C
Brand: Dynamic
The Dynamic Fluid Components high pressure hydraulic gear pump features all aluminum construction and produces displacement of 1.22 cu. in./rev. | *$185.99 |
| Prince Tie-Rod Cylinder - 3000 PSI, 5in. Bore, 16in. Stroke, 2in. Shaft
Brand: Prince
Tie-rod construction, double-acting, heavy-duty, high-strength tie rods. With ground and polished chromed piston rod, cast iron piston with O-ring seals and back up washers, polyurethane rod wiper, cast malleable rod clevis, zinc plated pins and clips. The maximum working PSI is 3000 and bursting PSI is 5000. Seal kits are available also. U.S.A. Max. PSI: 3,000, Bore Diameter (in.): 5, Stroke Length (in.): 16, Closed Pin Center (in.): 31 1/2, Shaft Diameter (in.): 2 | *$349.99 |
 | Prince Welded Tee Cylinder - 2500 PSI, 4in. Bore, 48in. Stroke, 2in. Shaft Size
Brand: Prince
Universal end mountings. A favorite for contractors, industrial, and agricultural applications. All steel welded construction: weld-on cross tube. Heavy wall steel tubing, ground and polished chrome piston rod with pin eye, cast iron piston. O-rings and back up washers, trac-type gland retainer. Maximum working PSI is 2500, bursting PSI is 5000. 2 1/2in. bore cylinders have 3/4in. pin holes. The 3in. and 3 1/2in. bore cylinders have 1in. pin holes. The 4in. bore cylinders have 1 1/4in. pin holes. 2 1/2in. bore cylinders have 3/8in. working ports. The rest have 1/2in. working ports. Double acting. Max. PSI: 2,500, Bore Diameter (in.): 4, Stroke Length (in.): 48, Closed Pin Center (in.): 58, Shaft Diameter (in.): 2 | *$419.99 |
 | Lion Welded Hydraulic Cylinder - 3000 PSI, 3in. Bore, 8in. Stroke, Model# 644828
Brand: Lion 3000
Double-acting, double-ported welded tie rods are perfect for industrial, agricultural and contractor applications. Features chrome rod, crown piston seals with wear ring, hallite rod seals, double lug base end, threaded rod end with ductile rod clevis and 3/4-16 ORB (SAE 8) ports inline with pins. 1in pin hole size. Complete with pins and cotter pins. | *$149.99 |
| De-Sta-Co Hydraulic Power Workholding, Threaded Cylinder, 1-12 thds., Stroke=.500 (1 Each)
Brand: De-Sta-Co Part Number: 010-210-702
Single-acting with spring return action, these cylinders can be used singly or combined by using a common manifold. Easily mounted. Can be used in any attitude and requires only a single inlet port. Threaded cylinders can be directly inserted into a fixture or used with mounting blocks. Locknuts, mounting blocks and end caps are available. Call for price and delivery. The 1-5/16" through 2-1/2" diameters are furnished with a radial port as well as axial. | *$98.18 |
 | Lion Heavy-Duty Tie-Rod Hydraulic Cylinder - 2500 PSI, 4in. Bore, 30in. Stroke, Model# 40TL30-200
Brand: Lion 2500
Built tough for agricultural and industrial applications. 2500 PSI model is designed to withstand shock loads of up to 5000 PSI. Durable ductile iron cast components. 90 durometer O-ring seals with anti-extrusion rings for positive sealing throughout the cylinder. High-tensile steel shaft is precision ground, polished and hard chrome-plated. Max. PSI: 2,500, Bore Diameter (in.): 4, Stroke Length (in.): 30, Closed Pin Center (in.): 40 1/4, Shaft Diameter (in.): 2 | *$249.99 |
| Dynamic Fluid Components High Pressure Hydraulic Gear Pump - 2900 Max. PSI, Spline 9-Tooth Shaft, Model# GP-F20-20-S9-C
Brand: Dynamic
The Dynamic Fluid Components high pressure hydraulic gear pump features all aluminum construction and produces displacement of 1.22 cu. in./rev. | *$185.99 |
 | Dynamic Fluid Components High Pressure Hydraulic Gear Pump - 3650 Max. PSI, 3/4in. Shaft, Model# GP-F20-14-P1-C
Brand: Dynamic
The Dynamic Fluid Components high pressure hydraulic gear pump features all aluminum construction and produces displacement of 0.85 cu. in./rev. | *$185.99 |
| Lion Heavy-Duty Tie-Rod Hydraulic Cylinder - 2500 PSI, 2in. Bore, 18in. Stroke, Model# 20TL18-112
Brand: Lion 2500
Built tough for agricultural and industrial applications. 2500 PSI model is designed to withstand shock loads of up to 5000 PSI. Durable ductile iron cast components. 90 durometer O-ring seals with anti-extrusion rings for positive sealing throughout the cylinder. High-tensile steel shaft is precision ground, polished and hard chrome-plated. Max. PSI: 2,500, Bore Diameter (in.): 2, Stroke Length (in.): 18, Closed Pin Center (in.): 28 1/4, Shaft Diameter (in.): 1 1/8 | *$109.99 |
| Lion Heavy-Duty Tie-Rod Hydraulic Cylinder - 2500 PSI, 3in. Bore, 6in. Stroke, Model# 30TL06-125
Brand: Lion 2500
Built tough for agricultural and industrial applications. 2500 PSI model is designed to withstand shock loads of up to 5000 PSI. Durable ductile iron cast components. 90 durometer O-ring seals with anti-extrusion rings for positive sealing throughout the cylinder. High-tensile steel shaft is precision ground, polished and hard chrome-plated. Max. PSI: 2,500, Bore Diameter (in.): 3, Stroke Length (in.): 6, Closed Pin Center (in.): 16 1/4, Shaft Diameter (in.): 1 1/4 | *$89.99 |
 | Enerpac Hydraulic Power Workholding Single Acting Manifold Cylinder, No. TS-2131ST (1 Each)
Brand: Enerpac Part Number: CST-2131
These threaded miniature cylinders were designed specifically for tooling. All cylinders are single-acting with spring return action for rapid work release. They have threaded bodies for all types of mountings. Cylinders may be inserted directly in a fixture or used with standard brackets. Stainless steel construction. Maximum operating pressure 5,000 psi. See our full line catalog for accessories. | *$95.00 |
 | De-Sta-Co Hydraulic Power Workholding, Jam Nut, B=1 3/8-18 (1 Each)
Brand: De-Sta-Co Part Number: 051-137-180 | *$27.60 |
| De-Sta-Co Hydraulic Power Workholding, Threaded Body Cylinder, Single Acting, D=1.875-16, K=5/16-24 (1 Each)
Brand: De-Sta-Co Part Number: 010-012-221 | *$159.53 |
 | Enerpac Hydraulic Power Workholding No. STRD121, Light Duty, Double Acting, Threaded, w/o Arm (1 Each)
Brand: Enerpac Part Number: STRD-121
Hydraulic Power Workholding - Light Duty - These swing cylinders rotate 90° as they begin their stroke, continuing without rotation for the final clamping stroke. Cylinders can be changed to left swing, right swing or pull applications by loosening the bottom plug. All single acting cylinders come with a retract spring for single-acting operations. Max. psi 5,000. Clamp arms not included but sold separately below. Body styles available are threaded with upper flange or non-threaded with lower or upper flange. | *$398.00 |
|
