 | 3/4 NPT, Parker Piggy Back Filter / Regulators w/Gauge (1 Each)
Brand: Reid Supply Company Part Number: MFP-369
"Piggyback" Filter/Regulators with Gauge - Integral filter/regulator "piggybacks" are an excellent choice where accurate pressure regulation and high moisture removal efficiency are required in a space saving package. Pressure rating 150 psi and a temperature range of 32°F to 125°F. Polycarbonate bowl and manual drain are standard on units. 67 SCFM flow rate. Comes with a 40 micron filter. | *$94.44 |
 | 5/8 Bore x 2. Stroke, Double Acting, Stud Mount, Clippard Stainless Steel Pneumatic Cylinders (1 Each)
Brand: Reid Supply Company Part Number: PAC-85
5/8" Bore Stud Mount Double Acting | *$17.73 |
| | 1/2 Bore x 1. Stroke, Double Acting, Stud Mount, Clippard Stainless Steel Pneumatic Cylinders (1 Each)
Brand: Reid Supply Company Part Number: PAC-25
1/2" Bore Stud Mount Double Acting | *$15.84 |
 | 0.1 to 30 Seconds, Off Delay, Parker Time Delays Relays (1 Each)
Brand: Reid Supply Company Part Number: MFP-483
Time Delays Relays - Requires timer sub base. (Sold separately). | *$169.09 |
 | 1/8 NPT, 12 V DC, 3-Way Body Ported, ARO Selenoid Valves (1 Each)
Brand: Reid Supply Company Part Number: ARO-405
Solenoid Valves - The 3-way and 4-way valves are 2-position, with a single solenoid and spring return. Valves are direct acting and have a non-locking manual override. Stacking models are great for multi-valve applications where space is limited. CFM on all models is 6.9; Cv is 0.2. Maximum temperature range is 0° to 180°F. Maximum operating pressure is 120 psi. | *$46.29 |
 | 1/4 NPT Port, 14 SCFM Flow, 2-120 Spring Range, ARO Precision Air Regulators (1 Each)
Brand: Reid Supply Company Part Number: ARO-5
Precision Air Regulators - High precision multi-stage pressure regulators. Controls output pressure with an accuracy of 0.1%, and very low sensitivity to changes in supply pressure and flow. High degree of regulation and repeatability are achievable by reacting to down stream pressure fluctuations as small as 0.01 psi above set pressure. Movement as small as 0.0001 inches will cause main valve to correct to the proper position. At start up, regulated pressure will return to its output setting, even after long down times. Maximum pressure 150 psi. Temperature rating 20°F to 150°F. | *$106.19 |
 | 3/8 NPT Ports, 3/4 Inlet, 8 Port, 1.50 Hex. x 11. Lg., Aluminum Manifolds, Black (1 Each)
Brand: Reid Supply Company Part Number: NM-207
Aluminum - Ready to use, no threading required. Positive seal. Use with brass or steel fittings. Hardcoat color anodized finish available in black, blue, or red. Other sizes, hole configurations and colors available as special orders. Please call for price and delivery. Automotive tested approval. Tensile 38,000 psi, yield 35,000 psi. Hardened to T6511. Can withstand pH 4.5. Honed ID. Dipped to remove blemishes and chips. Brackets are sold separately. | *$54.82 |
 | 3/4 Bore x 2. Stroke, Double Acting - Rear Pivot Mount, Parker Air Cylinders (1 Each)
Brand: Reid Supply Company Part Number: MFP-67
Rear Pivot Mount - Double Acting - MFP-62 through MFP-106 include a mounting nut. | *$34.83 |
 | 1/4 NPT, Parker Lubricators (1 Each)
Brand: Reid Supply Company Part Number: MFP-360
Lubricators - These lubricators are designed to provide optimum and uniform lubrication with fine micro-mist particles of two micron or smaller. Units should be installed close to the application, ensuring effective distribution of oil to pneumatic components. All units have a polycarbonate bowl. Metal bowl guards sold separately. Maximum pressure is 150 psi and temperature range of 32°F to 125°F. | *$34.16 |
 | 3/8 NPT, 3/8 Tube SizeParker Right Angle Flow Controls w/Presto Lock Fittings (1 Each)
Brand: Reid Supply Company Part Number: MFP-328
Right Angle Flow Controls with Presto Lock Fittings | *$34.37 |
 | 3/8 NPT Ports, 24 V AC, Three Position Double Exhaust Center Type, Parker Directional Solenoid Valves (1 Each)
Brand: Reid Supply Company Part Number: MFP-440
Directional Solenoid Valves - Parker valves are high performance valves that utilize the WCS (Wear Compensation System) to provide wear compensated sealing for non-lube service through millions of cycles. Valves are ideal for packaging, assembly and factory floor automation applications. Instructions included. | *$158.89 |
 | 3. Bore x 6. Stroke, Double Acting - Front Nose Mount, Parker Air Cylinders (1 Each)
Brand: Reid Supply Company Part Number: MFP-36
Front Nose Mount - Double Acting | *$166.30 |
 | 3/8 NPT Ports, 1/2 NPT Inlet, 8 Port, 1.50 W x 8.75 Lg., Aluminum Double Sided Ports - 90 Degree Manifolds, Black (1 Each)
Brand: Reid Supply Company Part Number: MM-820
Double Sided Ports - 90° | *$38.43 |
 | Parker 40 Micron Filter Elements, Use w/MFP-357, 358, 359, 368, 369 (1 Each)
Brand: Reid Supply Company Part Number: MFP-513
40 Micron Filter Elements | *$19.50 |
 | Mounting Brackets for 3/4 inlet Size (1 Each)
Brand: Reid Supply Company Part Number: NM-105
Mounting Bracket | *$6.69 |
 | 1/8 NPT, 1.13 OAL, Parker Exhaust Mufflers (1 Each)
Brand: Reid Supply Company Part Number: MFP-200
Exhaust Port Mufflers | *$8.80 |
 | 2 1/2 Bore x 2. Stroke, Double Acting, Compact, ARO Composite Air Cylinders (1 Each)
Brand: Reid Supply Company Part Number: ARO-710
Cylinders are double acting, with a single rod end. Cylinder barrel is made from a unique cross-wound thermo set epoxy. This creates a very strong and lightweight cylinder. The high impact resistance reduces the chances of cylinder failure due to dings or dents. Interior surface is self-lubricating, which insures highly reliable performance and an extended seal life. Cylinder heads are clear anodized aluminum alloy with stainless steel tie bolts. Maximum pressure is 200 psi. Cylinder temperature rating is -25°F to +225°F. | *$122.22 |
| 3/8 NPT, 1.50 OAL, Parker Exhaust Mufflers (1 Each)
Brand: Reid Supply Company Part Number: MFP-202
Exhaust Port Mufflers | *$11.67 |
 | Foot Mounting Brackets, Use w/Bore Size 2., 2 1/2 (1 Each)
Brand: Reid Supply Company Part Number: PAC-890
Foot Mounting Brackets | *$8.53 |
 | 3/8 NPT, 1.94 Lg. Open, 11/16 Hex., Parker Muffler / Speed Controls (1 Each)
Brand: Reid Supply Company Part Number: MFP-331
Muffler/Speed Control | *$19.18 |
| 3. Bore x 3. Stroke, Double Acting - Rear Pivot Mount, Parker Air Cylinders (1 Each)
Brand: Reid Supply Company Part Number: MFP-114
Rear Pivot Mount - Double Acting - MFP-62 through MFP-106 include a mounting nut. | *$170.96 |
 | 3/8 NPT Ports, 1. Inlet, 16 Port, Nylon Manifolds, Blue (1 Each)
Brand: Reid Supply Company Part Number: NM-14
Nylon - An economical replacement to steel manifolds. Nylon manifolds are molded from specialty-blended nylon material that is extremely durable and resistant to impact and corrosion. Used for air, water, lubricants or coolants in various applications. The nylon, with 6% fiberglass fill construction, allows leak-free NPT pipe connections. Can be used with steel or brass fittings. Marked in and out and numbered porting for easy installation and identification. | *$59.05 |
 | 1/4 NPT Ports, 3/8 NPT Inlet, 4 Port, 1.25 W x 4.12 Lg., Aluminum Double Sided Ports - 90 Degree Manifolds, Black (1 Each)
Brand: Reid Supply Company Part Number: MM-610
Double Sided Ports - 90° | *$21.96 |
| 2. Bore x 6. Stroke, Double Acting - Rear Pivot Mount, Parker Air Cylinders (1 Each)
Brand: Reid Supply Company Part Number: MFP-111
Rear Pivot Mount - Double Acting - MFP-62 through MFP-106 include a mounting nut. | *$107.07 |
| 3/8 NPT Ports, 1. Inlet, 4 Port, 1.75 Hex. x 11. Lg., Aluminum Manifolds, Black (1 Each)
Brand: Reid Supply Company Part Number: NM-203
Aluminum - Ready to use, no threading required. Positive seal. Use with brass or steel fittings. Hardcoat color anodized finish available in black, blue, or red. Other sizes, hole configurations and colors available as special orders. Please call for price and delivery. Automotive tested approval. Tensile 38,000 psi, yield 35,000 psi. Hardened to T6511. Can withstand pH 4.5. Honed ID. Dipped to remove blemishes and chips. Brackets are sold separately. | *$45.79 |
 | 3/8 NPT Ports, 1. Inlet, 8 Port, 1.75 Hex. x 11. Lg., Aluminum Manifolds, Red (1 Each)
Brand: Reid Supply Company Part Number: NM-422
Aluminum - Ready to use, no threading required. Positive seal. Use with brass or steel fittings. Hardcoat color anodized finish available in black, blue, or red. Other sizes, hole configurations and colors available as special orders. Please call for price and delivery. Automotive tested approval. Tensile 38,000 psi, yield 35,000 psi. Hardened to T6511. Can withstand pH 4.5. Honed ID. Dipped to remove blemishes and chips. Brackets are sold separately. | *$67.06 |
 | 1/2 NPT, Parker Regulators w/Gauge (1 Each)
Brand: Reid Supply Company Part Number: MFP-366
Regulators with Gauge - These regulators are designed to provide quick response and accurate pressure regulation for the most demanding industrial applications. Rolling diaphragm design gives repeatable performance with low hysteresis over a wide range of pressures. Pressure range is 2-125 psi and temperature range is 32°F to 125°F. | *$61.99 |
 | 1/8 NPT Port, 5/32 Pilot Port, Parker Blocking Valves w/Threaded Connection (1 Each)
Brand: Reid Supply Company Part Number: MFP-487
Blocking Valves w/Threaded Connection - Blocking valves are designed for precise repeatable stopping of moving cylinders or to maintain the position of a cylinder in the event of an air pilot signal loss. Blockers are used for positioning, jogging, and safety purposes. Operating pressure is 0 -150 psi with a temperature range of 5°F to 140°F. Maximum operating frequency is 10 Hz with a life expectancy of 10 million cycles at 90 psi, 68°F, dry air and 1 Hz operating frequency. | *$79.33 |
 | Parker Relief Valves, Brass Body (1 Each)
Brand: Reid Supply Company Part Number: MFP-1020
Relief Valves - Protect against excessive pressure buildup in pneumatic circuit or system. For use where gradual proportional relief is required. Maximum inlet pressure is 300 psi. Relief range is 0 to 100 psi. Spring range is 0 to 15 psi. Operating temperature is 40°F to 120°F. | *$27.49 |
 | 3/8 NPT Ports, 1. Inlet, 4 Port, Nylon Manifolds, Blue (1 Each)
Brand: Reid Supply Company Part Number: NM-02
Nylon - An economical replacement to steel manifolds. Nylon manifolds are molded from specialty-blended nylon material that is extremely durable and resistant to impact and corrosion. Used for air, water, lubricants or coolants in various applications. The nylon, with 6% fiberglass fill construction, allows leak-free NPT pipe connections. Can be used with steel or brass fittings. Marked in and out and numbered porting for easy installation and identification. | *$28.50 |
| 1 1/2 Bore x 8. Stroke, Double Acting - Rear Pivot Mount, Parker Air Cylinders (1 Each)
Brand: Reid Supply Company Part Number: MFP-106
Rear Pivot Mount - Double Acting - MFP-62 through MFP-106 include a mounting nut. | *$79.66 |
 | 1/2 NPT, 3.19 OAL, Parker Exhaust Port Silencers (1 Each)
Brand: Reid Supply Company Part Number: MFP-212
Exhaust Port Silencers | *$21.87 |
 | 3. Bore x 1. Stroke, Double Acting - Low Profile, Parker Air Cylinders (1 Each)
Brand: Reid Supply Company Part Number: MFP-242
Low Profile - Parker low profile cylinders are designed to meet the demands for saving space. The cylinder body is made of heavy wall aluminum alloy. The tube ID coating has extreme hardness, excellent wear, seizure resistance, low coefficient of friction and high corrosion resistance. The piston rod is made of high strength steel, hard chrome plated for smooth performance, and extended seal wear. The piston seal and the piston rod seal are made of Buna-N material for positive sealing. Maximum operating pressure 250 psi with an operating temperature range of -10°F to 165°F. Other sizes are available as special order. Please call for price and delivery. | *$170.19 |
 | 1/2 Bore x 1. Stroke, Double Acting, Universal Mount, Clippard Stainless Steel Pneumatic Cylinders (1 Each)
Brand: Reid Supply Company Part Number: PAC-50
1/2" Bore Universal Mount Double Acting | *$18.37 |
 | 1/2 NPT Ports, 1. NPT Inlet, 4 Port, 2.25 W x 9.75 Lg., Aluminum Single Sided Port Manifolds (1 Each)
Brand: Reid Supply Company Part Number: MM-250
Single Sided Ports - Provides a convenient junction point for branching off a single line on distribution systems. Can be used on air, hydraulic, water, coolant, machine and other distribution lines. Made of 6061 aluminum with black anodized finish unless noted below. Eight drilled mounting holes (two per side). Operating pressure: 1,000 psi air and, 5,000 psi non-shock hydraulic. All threads are NPT. Other lengths, threads and number of holes as well as custom sizes and configurations are available as special order. Please call for price and delivery for sizes not listed below. | *$51.40 |
 | 2. Bore x 1. Stroke, Double Acting, Universal Mount, Clippard Stainless Steel Pneumatic Cylinders (1 Each)
Brand: Reid Supply Company Part Number: PAC-310
2" Bore Universal Mount Double Acting | *$60.97 |
| | 1/2 Bore x 1/2 Stroke, Double Acting, Stud Mount, Clippard Stainless Steel Pneumatic Cylinders (1 Each)
Brand: Reid Supply Company Part Number: PAC-20
1/2" Bore Stud Mount Double Acting | *$15.10 |
| Parker 40 Micron Filter Elements, Use w/MFP-354, 355, 356 (1 Each)
Brand: Reid Supply Company Part Number: MFP-512
40 Micron Filter Elements | *$19.49 |
 | 1/4 NPT Ports, 1. Inlet, 8 Port, w/Solid Plug in center, Nylon Manifolds, Blue (1 Each)
Brand: Reid Supply Company Part Number: NM-09
Nylon - An economical replacement to steel manifolds. Nylon manifolds are molded from specialty-blended nylon material that is extremely durable and resistant to impact and corrosion. Used for air, water, lubricants or coolants in various applications. The nylon, with 6% fiberglass fill construction, allows leak-free NPT pipe connections. Can be used with steel or brass fittings. Marked in and out and numbered porting for easy installation and identification. | *$47.16 |
| 1/2 NPT Ports, 1 1/2 Inlet, 16 Port, 2.50 Hex. x 19. Lg., Aluminum Manifolds, Black (1 Each)
Brand: Reid Supply Company Part Number: NM-220
Aluminum - Ready to use, no threading required. Positive seal. Use with brass or steel fittings. Hardcoat color anodized finish available in black, blue, or red. Other sizes, hole configurations and colors available as special orders. Please call for price and delivery. Automotive tested approval. Tensile 38,000 psi, yield 35,000 psi. Hardened to T6511. Can withstand pH 4.5. Honed ID. Dipped to remove blemishes and chips. Brackets are sold separately. | *$106.68 |
| Mounting Brackets for 1 1/2 inlet Size (1 Each)
Brand: Reid Supply Company Part Number: NM-107
Mounting Bracket | *$7.68 |
| 3. Bore x 4. Stroke, Double Acting - Front Nose Mount, Parker Air Cylinders (1 Each)
Brand: Reid Supply Company Part Number: MFP-34
Front Nose Mount - Double Acting | *$157.14 |
 | 1/2 NPT, 3-Way, Parker Lockout Valves (1 Each)
Brand: Reid Supply Company Part Number: MFP-342
Lockout Valves Three-Way - Lockout valves are made of cast aluminum alloy with a metal handle for durability. Bright color for high visibility. Complies with O.S.H.A. Standard 29 CFR part 1910. Operating pressure range of 0 to 250 psi and a temperature range of 32°F to 160°F. Cv range of 3.0 to 10.0. All valves have a 1" exhaust port. All parts have a silencer included. | *$216.00 |
 | 1/2 NPT Port, 85.3 SCFM Flow, ARO Needle Valves (1 Each)
Brand: Reid Supply Company Part Number: ARO-390
Composite Needle, Check and Flow Control Valves - Composite body is 30% glass filled polyester. Tough and corrosion resistant. Color-coded micrometer and calibrated adjustment knob provide instant reference points. Press red locking ring down to prevent adjustment. Operating temperature is 0°F to 200°F. Operating pressure is 200 psi. max. | *$34.81 |
 | 5/8 Bore x 2. Stroke, Double Acting, Universal Mount, Clippard Stainless Steel Pneumatic Cylinders (1 Each)
Brand: Reid Supply Company Part Number: PAC-115
5/8" Bore Universal Mount Double Acting | *$20.60 |
 | 3/8 NPT, 3 Unit, Parker Combination FRL's (1 Each)
Brand: Reid Supply Company Part Number: MFP-352
Combination FRL'S | *$99.11 |
| 3/8 NPT Ports, 1/2 NPT Inlet, 4 Port, 1.50 W x 4.75 Lg., Aluminum Double Sided Ports - 90 Degree Manifolds, Black (1 Each)
Brand: Reid Supply Company Part Number: MM-620
Double Sided Ports - 90° | *$24.63 |
 | Clevis Mounting Brackets, Use w/Bore Sizes 1/2, 5/8 (1 Each)
Brand: Reid Supply Company Part Number: PAC-720
Clevis Mounting Brackets | *$3.78 |
 | 7/16 Bore x 3. Stroke, Double Acting - Front Block Mount, Parker Air Cylinders (1 Each)
Brand: Reid Supply Company Part Number: MFP-54
Front Block Mount - Double Acting | *$40.16 |
| 1/8 NPT, 120 V AC, 3-Way Body Ported, ARO Selenoid Valves (1 Each)
Brand: Reid Supply Company Part Number: ARO-395
Solenoid Valves - The 3-way and 4-way valves are 2-position, with a single solenoid and spring return. Valves are direct acting and have a non-locking manual override. Stacking models are great for multi-valve applications where space is limited. CFM on all models is 6.9; Cv is 0.2. Maximum temperature range is 0° to 180°F. Maximum operating pressure is 120 psi. | *$46.29 |
|
