 | C.R. LAURENCE 0377111 CRL Panther Edger 110 Volt Coolant Pump
Brand: C.R. Laurence Part Number: 0377111
Designed for CRL's Panther Edger This high quality pump was designed for use with the CRL Panther Edger . It delivers Coolant to the Grinding Wheel and at the same time it lubricates the surrounding machine parts. The pump sits in the tank and usually works best if it is suspended from the bottom, as it will not be as prone to contaminants. Periodic cleaning of the sediment screen will prolong the life of the pump. | *$146.13 |
 | C.R. LAURENCE 38709701 Somaca/CRL VE4 Flat and Seam Edge 120-140 Grit Grinding Wheel for 1/4 to 1/2 Glass
Brand: C.R. Laurence Part Number: 38709701
120-140 Grit Somaca/CRL VE4 Flat and Seam Edge Grinding Wheels are available for 1/8 to 3/4 inch (3 to 19 millimeter) thick glass and grits from 120 to 325. Dimensions: 7 in (178 mm) | *$663.93 |
| | Hitch Pin Hair Pin Clips - 410X HITCH PIN .177 WIRE DIA.
Brand: Various Part Number: 410X
Hitch Pin Hair Pin Clips - Manufactured of Oil Tempered Spring Wire, Plated. 100/Pack. Ordering Information: * 223P - 3/64" size category, .042 wire diam, 3/64" drill hole size, 3/16" minimum shaft di | *$1.01 |
 | CRL 62" Replacement Diamond Coated Blade - DTB5000
Brand: C.R. Laurence Part Number: DTB101
For CRL Diamond Laser Band Saw This CRL Diamond Coated Replacement Blade is designed for use on the CRL DTB5000 Diamond Laser Band Saw . | *$193.16 |
 | C.R. LAURENCE 3766400 Somaca/CRL VE4 Rubber Polishing Wheel 400 Grit for 1/4 to 1/2 Glass
Brand: C.R. Laurence Part Number: 3766400
400 Grit Somaca/CRL VE4 Rubber Polishing Wheels are available in 120, 180, and 400 grits for glass 1/4 to 1 inch (6 to 25 millimeter) thick. Dimensions: 8 x 3/4 in (203.2 x 19 mm) | *$71.21 |
 | Special Products Co/ Farmex 03056 Replacement Top Link And Lift Arm Ball
Brand: Special Products Co/ Farmex Part Number: 03056
Designed to replace top link and lift arm balls. Zinc plated. No. 03054: Replaces John Deere model No. F2680 and Oliver model No. 105968A, pin hole size: 3 4", length thru bore: 1 3 4", ball diameter: 2" No. 03055: Replaces John Deere model No. F2681 and | *$4.62 |
 | C.R. LAURENCE CN0017 CRL Top Wheel Bracket for the GL4W or CN4106 Sander
Brand: C.R. Laurence Part Number: CN0017
Designed for CRL GL4W/CN4106 Sanders This CRL Top Wheel Bracket is designed to fit the CRL GL4W or CN4106 (Canadian Model) upright sander as an O.E.M replacement part. It can easily be replaced with common hand tools. | *$223.86 |
 | C.R. LAURENCE CN0035 CRL Top Pulley Shaft and Bearing for the GL4W or CN4106 Sander
Brand: C.R. Laurence Part Number: CN0035
Designed for CRL GL4W/CN4106 Sanders This CRL Top Pulley Shaft and Bearing is designed to fit the CRL GL4W or CN4106 (Canadian Model) upright sander as an O.E.M replacement part. It can easily be replaced with common hand tools | *$106.84 |
 | Do it Best Imp/Fence 718138 Poultry Netting
Brand: Do it Best Part Number: 718138
Hexagon. 20 gauge wire galvanized before weaving. 150' per roll. Available in 1'' and 2'' openings. No. 718076: 1 x 20, 12'' x 150' No. 718085: 1 x 20, 18'' x 150' No. 718094: 1 x 20, 24'' x 150' No. 718110: 1 x 20, 36'' x 150' No. 718129: 1 x 20, 48'' x 150' No. 718138: 1 x 20, 60'' x 150' No. 718147: 1 x 20, 72'' x 150' No. 718156: 2 x 20, 24'' x 150' No. 718165: 2 x 20, 36'' x 150' No. 718174: 2 x 20, 48'' x 150' No. 718183: 2 x 20, 60'' x 150' No. 718192: 2 x 20, 72'' x 150' | *$129.99 |
 | Battery Operated Fencers - BATTERY OPERATED FENCER
Brand: Hol-dem Part Number: S-21
Battery Operated Fencers - *Charges up to 10 miles of clean fence(12 volt) *UL Listed* Battery life: 12 volt approximately 3 to 4 weeks/6 volt approximately 4 to 5 weeks *Controls most animals. *Di | *$48.50 |
 | C.R. LAURENCE 2200 CRL 4 X 106 Wet Abrasive Belt Sander Without Roller Platen
Brand: C.R. Laurence Part Number: 2200
New Fiberglass Tank Won't Rust Rugged Construction and a One H.P. Direct-Drive Motor Also Available for Australia with 240 v. 50 Hz. Power Streamlined styling, rugged construction and the affordable price makes our CRL Upright Wet Belt Sander without Platen ideal for use by glass fabricators and processors. The CRL Wet Belt Sander is designed to use the most popular size four by 106 inches (101.6 by 2692.4 millimeters) wet or dry abrasive belts to sand edges to the desired finish. Features of the 2200 Sanding Machine include Direct drive, one H.P., 60 cycle, 110 Volt AC Motor Five Inch (127 millimeter) Diameter Drive Pulley Motor can be wired for 220 Volts at an additional cost. Our New CRL 2200SS Belt Guard Safety Shield helps protect the operator in the event of accidental belt breakage. To solve the problem of water tank spray corrosion, we've replaced the steel tank with a Non-Rusting Fiberglass Water Tank. Securely fastened with six mounting bolts, the tank is trimmed with rugged U-Channel. When you consider all of these features, it's easy to see why glass shops large and small have made the 2200 the glass industry's most popular Upright Belt Sander. For more information, or machine specifications, contact us at (888) 663-9830, or email us here . BELT SELECTION: CRL Wet Abrasive Belts in the four by 106 inch size are recommended for the 2200. The most popular are the: CRL4X106120X 120X Grit Smooth Finish, and Cat. No. CRL4X10680X 80X Grit Rough Finish, but other grits from 36X (Super Coarse) to 600X (Super Fine) are available for this machine, along with Cork Belts for high polishing. | *$2,747.92 |
 | Ideal 35-828 Power Ship Auger, 1-1/8 Inch
Brand: Ideal Part Number: 35-828
Ideal 35-828 Nailbiter Power Ship Auger, 1-1/8 InchIDEAL brings you products that make your job easier; products that you can rely on, with warranties you can trust; products that are available whenever and wherever you need them. Ideal Industries divisions are dedicated to the professionals in the Electrical, DataComm, Wire Processing and OEM Connections markets.Ideal 35-828 Nailbiter Power Ship Auger, 1-1/8 Inch Features:; 17 inches long with 12 inches of twist; Drills through nails, wood, and other materials; Full length heat treated and tempered for durability; Precision designed and cut screw point to resist breakage. | *$27.99 |
| | Hitch Pin Hair Pin Clips - HITCH PIN 3/32" .080 WIRE DIA.
Brand: Various Part Number: 217P
Hitch Pin Hair Pin Clips - Manufactured of Oil Tempered Spring Wire, Plated. 100/Pack. Ordering Information: * 223P - 3/64" size category, .042 wire diam, 3/64" drill hole size, 3/16" minimum shaft di | *$0.21 |
 | Columbus McKinnon M1225 Big Orange Wire Handle Hitch Pin
Brand: Columbus McKinnon Part Number: M1225
Hot forged pin. Micro allow steel. Folding wire handle. Easy to grip, easy to attach pull rope. Complete with hairpin lock. Orange painted. No. M1195: 1 2" pin diameter; 3 1 2" useable length, wire handle No. M1200: 5 8" pin diameter, 3 3 4" useable lengt | *$9.11 |
 | CRL 10" Diamond Glass Saw
Brand: C.R. Laurence Part Number: T10
Heavy-Duty, Sturdy Construction Rustproof Tank This CRL 10 Inch Diamond Saw makes straight and square custs accurately and quickly. Works best on 1/4 inch (6.4 millimeter) thick glass, and will cut glass up to four inches (102 millimeters) in height. Great for cutting super-hard or bulletproof glass. There is a solid plastic table top cutting surface and unbreakable plastic drip tank which cleans out easily. Maximum strip cut is 2-3/4 inches (70 millimeters) wide using the included guide. Maximum freehand cut is 5-3/4 inches (146 millimeters). Specifications: 1/3 HP Motor 1,740 RPM 110v AC Plastic Table Top | *$1,239.17 |
 | C.R. LAURENCE 2402503 CRL/Somaca 8 x 12 Counterbalanced Tilting Cutting Table With Breaker Bar and Air Flow 12 Outlet
Brand: C.R. Laurence Part Number: 2402503
Indoor/Outdoor Carpet: Cushions Glass and Protects Against Scratches This Somaca/CRL Counterbalanced Tilting Cutting Table is constructed of heavy gauge steel, electrically welded and painted. A full 3/4 inch smooth particle board table top and carpet is included. F.O.B : Cicero, Ill. | *$6,911.55 |
| Special Products Co/ Farmex 03054 Replacement Top Link And Lift Arm Ball
Brand: Special Products Co/ Farmex Part Number: 03054
Designed to replace top link and lift arm balls. Zinc plated. No. 03054: Replaces John Deere model No. F2680 and Oliver model No. 105968A, pin hole size: 3 4", length thru bore: 1 3 4", ball diameter: 2" No. 03055: Replaces John Deere model No. F2681 and | *$4.61 |
 | C.R. LAURENCE CN0006 CRL Water Spray Valve for the GL4W or CN4106 Sander
Brand: C.R. Laurence Part Number: CN0006
Easy to Replace Designed for the CRL GL4W/CN4106 Sanders This CRL Spray Valve is designed to fit the CRL GL4W or CN4106 (Canadian Model) upright sander as an O.E.M replacement part for older or clogged valves. Always unplug sander before attempting to replace any parts. | *$32.83 |
 | C.R. LAURENCE 30066909 CRL/Somaca Bearing Housing Assembly for BM106G Machine
Brand: C.R. Laurence Part Number: 30066909
Replacement Part for BM106G Wet Abrasive Upright Sander This part is for all (1987 to present) BM106G Wet Abrasive Belt Machines. Item Number on Schematic: 19 Quantity Required Per Machine: call | *$370.41 |
 | C.R. LAURENCE 2621004 CRL/Somaca 48 Glass Rest Extension Arm
Brand: C.R. Laurence Part Number: 2621004
One Piece 48" Extension Arm The 106's rubber roller platen work surface can be increased by the addition of this extension arm. The glass support bar becomes long enough to work the largest pieces of glass a single operator can safely handle. The 48 inch arm can easily replace the existing, standard 24 inch Somaca 106 glass platen rest bar. No hole drilling is required. | *$205.98 |
 | C.R. LAURENCE CN0039 CRL Lower Pulley for the GL4W or CN4106 Sander
Brand: C.R. Laurence Part Number: CN0039
Designed for CRL GL4W/CN4106 Sanders This CRL Lower Pulley is designed to fit the CRL GL4W or CN4106 (Canadian Model) upright sander as an O.E.M replacement part. It can easily be replaced with common hand tools. | *$214.41 |
 | C.R. LAURENCE 41910000 CRL/Somaca Solenoid Coil Parker Gold Ring # CFGC05 for BM106G Machine
Brand: C.R. Laurence Part Number: 41910000
Replacement Part for BM106G Wet Abrasive Upright Sander This part is for all (1987 to present) BM106G Wet Abrasive Belt Machines. Item Number on Schematic: 38 Quantity Required Per Machine: 1 | *$114.69 |
 | Keystone Steel Wire 70314 Nonclimb Horse Fence
Brand: Keystone Steel Wire Part Number: 70314
Class 1. Square Deal nonclimb. 2'' x 4'' horse fence. Top and bottom gauge: 10. Filler wire: 12 1 2. Rigid fencing yet flexible construction makes this ideal for installation over rolling meadows or hilly terrain. Superior strength and closely woven 2'' x 4'' vertical mesh pattern is specifically designed to prevent horses, cows, or hoofed animals from stepping through or walking down. 100' roll. No. 70310: 48'' high, 121 lb. No. 70314: 60'' high, 151 lb. | *$189.99 |
 | 50 each: Speeco Hitch Pin Clip (P7923)
Brand: SpeeCo Model: P7923 Part Number: P7923
Sold as one unit. (1 unit = 50 each.) Gold dichromate plating. Bulk. Fits Hitch Pins 3/8"-1/2" Dia. 3/22" Wire . Manufacturer number: P7923. SKU #: 71866. Country of origin: (TBA). Distributed by Special Speeco Products. | *$10.20 |
 | C.R. LAURENCE ERR1 CRL Stab-In Glass Cutting Table Rollers
Brand: C.R. Laurence Part Number: ERR1
Makes Glass Loading Easy When Table is in Upright Position Easy to Install and Remove CRL ERR1 Stab-In Glass Cutting Table Rollers make an efficient add-on to any tilt-top glass cutting table. The set of four durable rubber rollers mount into steel collars that are recessed into the table's surface. Positioned so they align with your vertical glass storage racks when your table is in the upright position, glass can be easily loaded onto the rollers safely. When the table is then lowered to the horizontal position, the rollers are simply pulled out of the steel collars so you're ready to cut glass. Four each per set. F.O.B : Red Oak, TX | *$1,224.44 |
 | C.R. LAURENCE 41900550 CRL/Somaca Parker Gold Ring OF20C-211OACF 1/4 Port for BM106G Machine
Brand: C.R. Laurence Part Number: 41900550
Replacement Part for BM106G Wet Abrasive Upright Sander This part is for all (1987 to present) BM106G Wet Abrasive Belt Machines. Item Number on Schematic: 37 Quantity Required Per Machine: 1 | *$70.35 |
 | C.R. LAURENCE EAF CRL Counter Balance Table Air Flotation System
Brand: C.R. Laurence Part Number: EAF
Easy to Install on any Glass Cutting Table Positions Glass on a Cushion of Air Safely and Easily 110 Volt Electrical Requirement Improve your cutting table by installing air flotation. The CRL Counter Balance Table Air Flotation System is easy to install, and allows you to float, move and easily turn glass on the table top. Contains a self-contained blower system, hose, and 12 check ball outlets. Number of Outlets: 12 Electrical Requirement: 110 Volts F.O.B : Red Oak, TX | *$1,672.67 |
| Ideal 35-815 Short Ship Auger, 1 Inch
Brand: Ideal Part Number: 35-815
Ideal 35-815 Nailbiter Short Ship Auger, 1 InchIDEAL brings you products that make your job easier; products that you can rely on, with warranties you can trust; products that are available whenever and wherever you need them. Ideal Industries divisions are dedicated to the professionals in the Electrical, DataComm, Wire Processing and OEM Connections markets.Ideal 35-815 Nailbiter Short Ship Auger, 1 Inch Features:; 7-1/2 inches long with 5 inches of twist; Drills through nails, wood, and other materials; Full length heat treated and tempered for durability; Precision designed and cut screw point to resist breakage. | *$39.45 |
 | C.R. LAURENCE 30118800 CRL/Somaca Open Cover Plate for BM106G Machine
Brand: C.R. Laurence Part Number: 30118800
Replacement Part for BM106G Wet Abrasive Upright Sander This part is for all (1987 to present) BM106G Wet Abrasive Belt Machines. Item Number on Schematic: 47 Quantity Required Per Machine: 1 | *$6.97 |
 | C.R. LAURENCE 2200735 CRL Replacement Bearings for Older Upper Pulleys
Brand: C.R. Laurence Part Number: 2200735
Used on Older Model 2200 Sanders Manufactured Before 1987 This CRL Replacement Bearing is used on older model sanders manufactured before June 1987 and fit the 2200750 shaft. Top quality materials are guaranteed to give you years of service. | *$246.55 |
 | C.R. LAURENCE 38533500 Somaca/CRL VE2 Plus 2/VE4 Flat and Seam Edge 170-200 Grit Grinding Wheel for 1/8 to 1/4 Glass
Brand: C.R. Laurence Part Number: 38533500
170-200 Grit Somaca/CRL VE2 Plus 2 and VE4 Pencil Edge Grinding Wheels are available for 1/8 to 3/4 inch (3 to 19 millimeter) thick glass and grits from 120 to 270. Dimensions: 7 in (178 mm) | *$544.67 |
 | Irwin 49915 I-100 Power Drill Auger Bit
Brand: Irwin Part Number: 49915
Dual purpose shank for use in hand braces and 3 8" and larger electric drills. Specially designed cutting head and screw point makes for cleaner and faster boring in all types of wood. Ground from special alloy tool steel, fully heat treated. Overall leng | *$10.47 |
 | C.R. LAURENCE AFCB1 CRL Air Float Chamber With Ball for Cutting Tables
Brand: C.R. Laurence Part Number: AFCB1
Replaces Worn or Damaged Units Replace your worn or damaged ball float units on your cutting table with the CRL Air Float Chamber with Ball . This unit is an OEM part for all CRL air flotation systems. | *$75.46 |
 | C.R. LAURENCE 2402544 CRL/Somaca 9 x 12 Counterbalanced Tilting Cutting Table With Air Flow 16 Outlet
Brand: C.R. Laurence Part Number: 2402544
Indoor/Outdoor Carpet: Cushions Glass and Protects Against Scratches This Somaca/CRL Counterbalanced Tilting Cutting Table is constructed of heavy gauge steel, electrically welded and painted. A full 3/4 inch smooth particle board table top and carpet is included. F.O.B : Cicero, Ill. | *$7,021.69 |
 | C.R. LAURENCE 33986 CRL 8 Plain Steel Disc
Brand: C.R. Laurence Part Number: 33986
C.R. LAURENCE 33986 CRL 8 Plain Steel Disc. Used on the CRL Glastar Studio Beveling System, this plain CRL Steel Disc functions as a backing plate only. Four different types of finishing pads mount to this steel plate with pressure sensitive adhesive. The system is supplied with four steel discs, many shops keep extra discs around for their extra diamond pads.. | *$16.52 |
 | C.R. LAURENCE CN0012 CRL 115 Volt Motor for the GL4W or CN4106 Sander
Brand: C.R. Laurence Part Number: CN0012
Designed to Fit the CRL GL4W/CN4106 Sanders This CRL 115 Volt Motor is designed to fit the CRL GL4W or CN4106 (Canadian Model) upright sander as an O.E.M replacement part. The heavy-duty, 1 HP motor runs at 3450 RPM and can be wired for 230 Volts by a qualified electrician. It carries a one year warranty. Safety Note: Always unplug sander before attempting to replace any parts. | *$555.45 |
| | C.R. LAURENCE 39472705 Somaca/CRL 8 Diamond Wheel for 1/2 Flat and Seam
Brand: C.R. Laurence Part Number: 39472705
120-140 Grit This Somaca/CRL 8" Diamond Wheel will grind a flat and seam edge profile on 1/2 inch (12 millimeter) glass and is designed to run on these bevelling machines: 752 (position 2), and 761 (position 3). Diameter: 8 in (203.2 mm) | *$799.09 |
| | Hitch Pin Hair Pin Clips - HITCH PIN 1/4" .243 WIRE DIA.
Brand: Various Part Number: 219P
Hitch Pin Hair Pin Clips - Manufactured of Oil Tempered Spring Wire, Plated. 100/Pack. Ordering Information: * 223P - 3/64" size category, .042 wire diam, 3/64" drill hole size, 3/16" minimum shaft di | *$1.07 |
| C.R. LAURENCE 2402513 CRL/Somaca 8 x 10 Counterbalanced Tilting Cutting Table With Breaker Bar and Air Flow 12 Outlet
Brand: C.R. Laurence Part Number: 2402513
Indoor/Outdoor Carpet: Cushions Glass and Protects Against Scratches This Somaca/CRL Counterbalanced Tilting Cutting Table is constructed of heavy gauge steel, electrically welded and painted. A full 3/4 inch smooth particle board table top and carpet is included. F.O.B : Cicero, Ill. | *$7,123.71 |
 | C.R. LAURENCE 39617200 Somaca/CRL 7 Flat and Small Seam Edge Grinding Wheel 170-200 Grit for 1/4 Glass
Brand: C.R. Laurence Part Number: 39617200
170-200 Grit Somaca/CRL Grinding Wheels are available for 1/8 to 3/4 inch (3 to 19 millimeter) thick glass and grits from 120 to 270. Dimensions: 7 in (178 mm) | *$530.98 |
 | Machinery Wire Fence Partition Door Post
Brand: Wireway Husky Part Number: G5506D
Machinery Partition Door Post Use these convenient door posts for easy installation of hinged door. 72"H x 2-12" sq. and 8" base. Bright yellow enamel finish. | *$82.95 |
 | C.R. LAURENCE CN0040 CRL Bottom Bracket Bearing for the GL4W or CN4106 Sander
Brand: C.R. Laurence Part Number: CN0040
Designed for CRL GL4W/CN4106 Sanders This CRL Bottom Bracket Bearing is designed to fit the CRL GL4W or CN4106 (Canadian Model) upright sander as an O.E.M replacement part. It can easily be replaced with common hand tools. | *$114.42 |
 | C.R. LAURENCE 39730201 Somaca/CRL 6 Diamond Flat Edge Cup 140-170 Grit for 1/8 to 1/2 Glass
Brand: C.R. Laurence Part Number: 39730201
140-170 Grit This Somaca/CRL 6" Diamond Cup Wheel will grind a flat edge profile on 1/8 to 1/2 inch (3 to 12 millimeter) glass and is designed to run on the VFE4 Cup Wheel Edger. Dimensions: 6 in (152.4 mm) | *$388.32 |
 | C.R. LAURENCE 2622000 CRL/Somaca 106 Wet Abrasive Belt Machine With Roller Platen - 110 Volt
Brand: C.R. Laurence Part Number: 2622000
Rough Grinding, Smoothing and Polishing Edges of Glass There are some quality products that never really get old – they just get better as the years pass. This is the case for the world famous Somaca 106" Belt Machine. It's a machine that has been the workhorse and mainstay for most glass shops in the U.S., Canada and throughout the world. Since 1932, glassworkers have learned to rely on the 106" to fulfill their glass grinding and polishing requirements. Reliability, versatility and durability are the words that best describe this renowned machine. A machine that has been made with pride by American craftsmen for over 70 years, using American-made components. Height: 72 in (1829 mm) Depth: 23 in (584 mm) Width: 24 in (610 mm) | *$2,719.71 |
 | C.R. LAURENCE STT1 CRL Stowaway Glass Cutting Table
Brand: C.R. Laurence Part Number: STT1
A Great Space Saver in the Shop High-Strength Construction Provides Durability Without Excess Weight 500 lb (225 kg) Load Capacity The Stowaway Glass Cutting Table features a generous work surface of 72-1/4 x 96-1/2 inches (1835 x 2450 millimeters) with a rugged, long-lasting felt top designed to reduce vacuum stick when used for cutting glass or other nonporous materials. High-strength construction provides durability without excess weight. Crossed support legs ensure a rigid and stable, 35 inch (889 millimeter) high work surface with a 500 pound (225 kilogram) load capacity. The scissor-action tilt design of the Stowaway floats the pivot point forward as the top lifts, providing nearly effortless manual tilt, without the extra weight of a counter-balanced system. Bronze pivot bushings and nylon washers make movements smooth and quiet. Rubber rollers support glass, laminate or other sheet materials when tilted and flip out of the way when not needed. Fold up the base section, pull back the stabilizing arm and the base is locked into place, ready to stow or roll. With its compact 25-3/4 inch (656 millimeter) deep x 79-3/4 inch (2028 millimeter) high profile, the Stowaway is easy to stow against a wall, roll along narrow aisles, slip through doorways, and fit on freight elevators. Weighing only 337 pounds (153 kilograms), it can even be lifted into the back of a truck for transport to a jobsite. Used as a rack for glass or other sheet materials, the Stowaway can be loaded from the front or from the side. Sheets roll easily and gently across the rubber support rollers. Some assembly required. F.O.B : Laurel, Montana | *$6,166.04 |
| C.R. LAURENCE 39579902 CRL/Somaca ME-II Orange Polish Wheel Double Wide
Brand: C.R. Laurence Part Number: 39579902
120 Grit Somaca/CRL ME-II Polish Wheels are available in Orange Polish and Rubber Polish for 1/8 inch to 1/2 inch thick glass. Dimensions: 8 in x 1-3/16 in (203 x 30.2 mm) Grit: 120 | *$132.06 |
 | Wire Grip Without Swivel - WIRE GRIP WITHOUT SWIVEL
Brand: Durbin Durco Part Number: 25
Wire Grip Without Swivel - * Manufactured from durable malleable iron. * Positive gripping surface. * Zinc plated, yellow chromate. * Without swivel. | *$14.37 |
 | C.R. LAURENCE BP2001 CRL Bar Platen for the 2200 and 2200RP
Brand: C.R. Laurence Part Number: BP2001
Fits Behind Belt Gives Glass a Slightly Rounded Edge This CRL Bar Platen is used behind the belt to give glass a slightly rounded edge. Must be inserted into PA100 Platen Adapter located on your Upright Belt Sander . | *$186.43 |
| Machinery Wire Fence Partition Hinged Door
Brand: Wireway Husky Part Number: G220405/
Machinery Partition Hinged Door 48"W x 60"H. Includes lock hasp. Add one or two doors to make space more accessible. Bright yellow enamel finish. Easy to install, remove or expand. | *$183.95 |
 | 10" Fence Plier - No Cutters
Brand: Raffael Tools Part Number: pli-f10
- Drop Forgedbr - Heat Treatedbr - Cushion Gripbr Weight: 1.85 Lbs | *$6.45 |
